Printing guide
Print your sashiko grid at actual size.
Download the PDF, select the matching paper size, print at 100% or Actual size, then measure the 50 mm check line. That short check is the best way to know your printed guide matches the dimensions you chose.
How do I print a sashiko grid without changing its size?
- Choose your paper in the generator. A4 is 210 × 297 mm. US Letter is 215.9 × 279.4 mm. Load that size into your printer.
- Download and open the PDF. Use the PDF viewer’s print command. Printing the website itself includes the controls and will not give you an accurate template.
- Select Actual size or 100%. Turn off Fit, Shrink to fit and Scale to printable area. Select one PDF page per sheet, portrait orientation and single-sided printing.
- Measure the check line. The horizontal line near the foot of each page must measure 50 mm between its end marks. Check it with a physical ruler before marking your fabric.
The screen is not a ruler. The preview adjusts to your screen. Its displayed centimetres will not match a ruler held against your monitor.
The download button tells you how many sheets you need. A guide that fits the printable area uses one page; larger guides are automatically divided across several. Paper margins, the heading and the scale check mean the usable guide area is smaller than the whole sheet.
How do I join a pattern printed across several pages?
Large PDFs keep your original measurements. They include a 10 mm strip of repeated pattern between neighbouring sheets, corner ticks and alignment crosses. The page heading identifies each sheet’s row and column.
- Check the scale on every sheet. Use the same printer settings for the whole PDF. If a 50 mm line is wrong, reprint that sheet before assembling the guide.
- Lay out the page order. Start with row 1, column 1. Work left to right across the first row, then begin the next row underneath it. The small sheet map in the generator shows this arrangement.
- Trim the blank margins that will cover a neighbour. For sheets after the first column, trim the left blank margin to the corner ticks. For sheets below the first row, trim the top blank margin. Keep the printed 10 mm overlap.
- Match the repeated pattern and crosses. Slide the next sheet over the previous one until the shared pattern lines coincide. Use the crosses on the untrimmed margins where available; hold the paper against a window or light source if that helps.
- Tape and check. Secure each join with small pieces of tape. Join the rows, then check the overall guide dimensions before transferring the design.
A 30 × 30 cm guide uses four sheets on either A4 or US Letter. A 45 × 30 cm guide uses six. A larger page count does not mean the pattern has been enlarged; it means the same full-size design has been split into more windows.
Overlap, rather than butt the edges together. The repeated 10 mm strip is intentional. Placing the printed edges side by side would add extra width or height to your design.
What does Fit whole repeats do?
By default, the pattern fills the exact guide dimensions and is cropped at the edges. Under More options, Fit whole repeats selects the largest number of complete rectangular repeat units that fit inside that area, then centres them. The scale stays fixed; any unused space becomes equal margins on opposite sides.
For example, a 123 × 123 mm square guide with 5 mm spacing can hold a 120 × 120 mm pattern of complete cells, leaving 1.5 mm on each side. Some motifs need larger repeat units: Seigaiha at a 5 mm base unit repeats over a 20 × 20 mm rectangle. The tool shows the resulting pattern area and margins.
A repeat unit is the block that tiles to make the design. Connected lines may still meet the edge of that block; fitting repeats does not isolate every leaf, circle or wave. If one repeat cannot fit, increase the guide dimensions or reduce the scale.
Grid spacing is different from stitch length
For square grids and dots, spacing is the distance between guide points. For decorative motifs, pattern scale is a base unit that controls the geometry. Most guides do not prescribe a stitch length. Kaki no Hana is an exception: each drawn surface stitch spans one base-unit grid cell. Use your chosen teacher’s instructions to decide how the drawing becomes stitches.
| Setting | Equivalent measurement | What it changes |
|---|---|---|
| 5 mm | 0.5 cm | Grid spacing or motif base unit |
| 10 mm | 1 cm | Grid spacing or motif base unit |
| ⅛ inch | 3.175 mm | Grid spacing or motif base unit |
| ¼ inch | 6.35 mm | Grid spacing or motif base unit |
How can I transfer a printed sashiko guide to fabric?
On fabric that lets enough light through, place the guide beneath the cloth and trace with a suitable removable fabric marker. For opaque fabric, use a transfer method intended for that material and follow its manufacturer’s instructions. Keep the fabric relaxed rather than stretched while marking.
Test both the marking and removal method on a scrap of the same fabric first. Dark cloth, loose weaves and textured materials may need a different approach. Keep the guide clear of seam allowances unless your project instructions specifically include them. Do not put ordinary fabric through a printer.
Should I download the PDF or SVG?
Choose PDF for home printing: it includes the paper size, page order and calibration lines. Choose SVG if you want a vector guide for a compatible drawing application. The SVG is one complete design at the selected millimetre dimensions, even when the PDF needs several sheets. It has no page headings, joining marks or scale line. Check its imported size before printing it elsewhere.
Why is my printed grid the wrong size?
The 50 mm line is too short or too long
The PDF viewer or printer has probably applied scaling. Select Actual size or 100%, and check the printer dialogue as well as the PDF viewer. Match A4 to A4 or Letter to Letter. Avoid multiple-pages-per-sheet and booklet settings.
The last row of cells looks smaller
With exact sizing, a partial cell is expected when the guide dimensions are not multiples of the spacing. Enable Fit whole repeats if you prefer full repeat units and centred margins.
The joins do not match
Check that all pages come from the same PDF and use the same print settings. Follow the row and column numbers and overlap the pattern by 10 mm. A cut through the printed overlap, or a sheet printed at a different scale, can prevent a clean join.
The lines are faint or an edge is missing
Try Deep ink instead of Soft grey. If the scale is correct but the printer clips an edge, check its printable margins. Keep Actual size selected; a printer with unusually large unprintable margins may need a different paper or printing service.
Still having trouble? Send the settings and a description of the problem through the contact options on Microapp.studio.